Chery QQ6 User Manual

Service Manual for Chery QQ6 (Electrical, Circuit) After Sales Service Department of Chery Automobile Sales Co., Ltd

1. Principle of Fog Lamp Control The fog lamp is controlled by the combination light switch which is used to control the op

2. Principle of Clearance Lamp Control The clearance lamp is controlled using a light switch. When the switch is in the clearance lamp position, the t

1. Principle of low beam lamp control When the light switch is in the headlamp position, the terminal 8# of the light swi

3. Principle of the passing lamp control When the light control switch is in PASS position (passing lamp position), the switch directly offers the hig

1. Principle of turn signal lamp control The turn signal lamp control is divided into three categories while the final control is implemented by the f

1. Control principle The electric rear-view mirrorr is controlled by a switch, without any relay. When the L position is selected, the Nos 2 and 3 ci

1. Control principle This wiper system’s control is a switch type one while the intermitten control adopts the intermitten relay. The wiper motor is g

Chapter Two Schematic Diagrams of Circuit Control I. Definition of Main Harness Connectors 发/前（发动机线束和前仓线束插接件） 前/仪 （前仓和仪表线束的 插件） 前/仪 （前仓和仪表线束

前/室（前仓和室内线束的插件）针脚定义针脚定义室/仪 （室内线束和仪表线束的插件） Compartment /Interior (Compartment and Interior Harness’s Connector) Interior/Instrument B (Interior Harnes

室/仪 （室内线束和仪表线束的插件） 室/左前 （室内线束和左前门线束的插件） 室/左前（室内线束和左前门线束的插件） 室 右前（室内线束和左前门线束的插件） 室/左后（室内线束和左后门线束的插件） Interior/Instrument A (Interior Harness and Inst

TABLES OF CONTENTS Chapter One Control Principle of Some Systems...4 I. Control Princ

室/左后（室内线束和左后门线束的插件） 室/右后（室内线束和右后门线束的插件） 室/右后（室内线束和右后门线束的插件） 室/后（室内线束和后背门线束的插件） （ 插头阵脚定义） Interior/RL B (Interior Harness and Rear Left Door Harness’s

（ 插头阵脚定义） II. Drawing Description 1. Main Symbol Description Symbol Meaning Symbol Meaning Circuit Connection Motor Fuse Position and SPeci

31– (GROUND): ground cable, from the negative electrode of the battery Wire diameter and color: 3. Definition of Main Controller In this schematic d

Grounding point of interior harness under the left A post. BCM grounding point at the side of BCM Groundin

III. Schematic Diagram of Main Electric Box and Module Position Engine’s ECU Instrument Electrical Box OBD Di

IV. Electrical Box Description 1. Instrument Electrical Box

V. Schematic Diagrams of Circuit Control 1. Starting and Charging System F17Ka15a1530a30

2. Electric Rear-View Mirror Ka15a1530a30/ // // // // /

3. Engine’s Anti-Theft System Ka15a1530a30

4. A/C and Defrost Systems 58Ka15a1530a30 / /11/ // // 42121

3. Engine’s Anti-Theft System...28 4. A/C and Defrost Systems...

5. Horn, Backup Lamp, Cigaretter Lighter, Ceiling Lamp and Luggage Boot Light 30- /1///27

6. Radio 58Ka15a1530a30////////////////

7. Front/Rear Wiper Ka15a1530a30/ // //// /

8. Turn Signal Lamp System 3030a15a15Ka222424// 3

9. Air Bag 30-Ka15a1530a30

10. Instrument System 8//// 41///////////

11. Engine’s Electronic Fuel Injection System / /// 111/42/ /（ ）/ // /1/3/ // // // // // 11227205#31r/39/38/27

12. BCM system DiagnosisFR Door LockFL Door LockAnti-theft IndicatorStarterAir Bag SignalRR Window MotorRL Window MotorFR Window MotorFL Windo

Chapter One Control Principle of Some Systems I. Control Principle of Starting System 1. Starting System When the ignition switch

operating. When the generator itself can generate electric power, the system will switch to the self-excitation mode. In addition, when the generator

II. BCM Control 1. Ceiling Lamp Control l When any door opens, the ceiling lamp lights automatically, and then extighuishes 15 minutes later after

l The door lock and window glass regulator can’t act at the same time, and the former is preferred if conflict. l Automatic door lock control (pre

arming indicator light continuously flashes; ③ if the ceiling lamp switch is in the controlled position and the ceiling lamp is in OPEN position, the

without the alarm horn). 4.6. Disalarm mode a) How to disalarm: After the body enters into the alarm mode: ① press down any pushbutton on the remote